Skip to content 
New system design and installation for homes off municipal water
Reliable water starts with a properly designed system. Whether you’re building a new home, adding an in-law suite, or replacing outdated equipment, we install complete well pump systems with properly sized pressure tanks, so your water runs steady and strong. From the very first tap in a new build to modernizing an older setup, our team makes sure your system is designed to last.
Serving Quinte West, Belleville, Trenton, Prince Edward County, and surrounding areas.
What we install
Submersible Well Pumps
- Quiet, efficient, and ideal for most drilled wells. Great lift capacity and fewer priming headaches than surface pumps.
Jet Pumps (Shallow & Deep-Well)
- A solid choice for shallow wells, dug wells, or shore wells. We size, prime, and protect them correctly to avoid nuisance issues.
Constant-Pressure Systems (VFD)
- Add a variable frequency drive so water pressure feels municipal: one smooth set-point, no big swings when multiple fixtures run.
Booster Pumps & Storage Integrations
- For low-yield wells, bulk-water storage, rain/gray systems, or trickle systems, we pair pumps, controls, and tanks so your house never “outruns” supply.
Pressure Tanks: the unsung hero of steady pressure
A pressure tank stores pressurized water and cushions the system so your pump doesn’t need to start every time someone turns on a tap.
Why sizing matters:
- Right-sized tank = fewer pump starts, longer pump life, quieter operation, and smoother pressure.
- Too small = rapid short-cycling, premature pump failure, pressure swings.
What we install: modern, pre-charged diaphragm/bladder tanks with corrosion-resistant fittings, proper pre-charge, and easy-to-service isolation valves.
When you might need a new system (not just a repair)
- You’re building or adding an accessory dwelling and need a new water system from the well in.
- Your current setup can’t keep up during peak use (shower + laundry + dishwasher = pressure crash).
- Frequent short-cycling (pump starts/stops every few seconds) or noisy operation.
- Old, undersized, or water-logged pressure tank.
- Upgrading from a jet pump to a submersible for better performance and efficiency.
- Switching to constant-pressure (VFD) to eliminate pressure swings.
- You’re pairing with trickle systems or water treatment and want the whole design right the first time.
- Already comparing repair vs. replacement? We’ll assess your existing equipment and give you both options in writing, no pressure, just the facts.
Signs your tank needs replacement
- Pump short-cycles (starts and stops rapidly)
- Visible rusting, sweating, or leaks
- Pressure swings or spitting air at fixtures
- Tank feels unusually light when tapped (lost pre-charge)
Our installation process for new systems (start-to-flow)
1. Site visit & flow/pressure assessment – We test static level, drawdown/flow (where applicable), and review household demand.
2. Design & sizing – Pump curve selection, pipe size, check valves, controls, and pressure tank sizing based on peak-use and cycling targets.
3. Clear proposal – Two to three options (good/better/best), timelines, and warranties.
4. Installation – Set/replace pump, new pitless (if required), sanitary well cap, trenching to the house, tank and controls, gauges, and reliefs.
5. Electrical & protection – Work with your licensed electrician on disconnects, grounding/bonding, surge protection, and generator compatibility where needed.
6. Disinfection & commissioning – Chlorinate, flush, start-up, pressure set-points, and leak/cycle tests.
7. Quality verification – Flow and pressure validation at fixtures, plus water treatment recommendations if tests show iron, hardness, sulphur, or bacteria.
8. Handover – Settings documented, warranty registered, maintenance checklist provided.
Why homeowners choose A1 for new installs
- Design first, then install. We size to performance targets, not just “what’s on the truck.”
- Local wells, local know-how. We understand the quirks of drilled, dug, and shore wells around Quinte/PEC.
- Future-proofing. Ready for softeners, iron filters, UV, and trickle systems, no repiping later.
- Clean, respectful work. We protect your home, label everything, and leave your mechanical space tidy.
- Transparent options. Repair vs. replace side-by-side, with expected lifespan and operating costs.
Maintenance & care (so your system lasts)
- Check pressure tank pre-charge annually.
- Replace air charge or tank as soon as short-cycling appears, don’t let the pump take the hit.
- Keep a clear mechanical space and don’t store it on the tank (no shelves on top).
- Schedule a performance check if pressure changes, you hear cycling at night, or water quality shifts.
Contact Us for Pumps & Wells Services
Need a new system or a professiona well upgrade? A1 Plumbing, Pumps & Water Treatment Inc., your trusted plumber Quinte West ON, designs and installs complete solutions for reliable, steady water.
Call us today at (613) 398-0599 or fill out our online form to request your free quote and get started with dependable Pumps & Wells services.